Check out Scat Products and Fast Fab Products Pages for more Engine related Products
Empi 3.5 qt Sump
£160.00 |
Empi Oil Pump Cover
£25.00 |
Kennedy Multi Finger Clutches Stage 1, 2 & 3
100% Load tested and jig assembled to insure proper pressure
Contact face is High-Tensile Cast-Iron Alloy for Maximum strength. Stage 1, 2 or 3 £105 |
|
Lightened 8 dowel Flywheel
We had a reputable machine shop select good used genuine VW flywheels, machine them for 8 dowels, resurface and lighten them and finally balance them and we now offer these for sale. £125 |
Flanged Crank Flywheel
We also stock the matching flywheels for VW style, J&G and Kennedy double disc clutch set-ups.
Prices from £250 |
Super Daikin Clutch Discs
High quality genuine Super Daikin clutch disc, not to be confused with Chinese
copy. £65 |
|
K Motion Valve Springs
K800 Valve springs for use with big valves, usually in Comp Eliminator / Super Flow / Angle Flow / 910 style heads.
£70 (set of 8) |
Scat 200mm Lightweight 4 Puck Clutch disc
Lightweight Quick*Silver stainless steel racing clutch disc (can be used on the street, but is very agressive) £30 |
CB Performance Valve Springs - VW650
VW650 Springs are designed for extreme endurance & are made from proprietary material that has unsurpassed high cycle fatigue life. For strip or street. These valve springs drop into heads machined for VW diameter dual springs & allow upto 630 lift if your heads are properly set up.
£105 |
CB Valve Spring Retainers
Chromoly £20.00 Allows dual springs in VW style heads. Titanium £75.00 Super strong and light, helps lighten valve train to allow more engine RPM |
CB Performance 1.4 Rockers
Forged from 4340 Chromoly steel
Set includes 8 rockers, 2 shafts, 4 rocker blocks, 4 Heavy Duty Chromoly Rocker Studs, adjusting shims kit, 2 end caps, and 2 bolts, 8 valve caps, 8 adjusting screws and lock nuts. £230 |
Carrillo Rods
5.8 Chevy Journal Carrillo Rods, these are as new they were used just to mock up and engine, but we have never run them.
£800 |
Wiseco Piston Kits
We stock both common styles of Wiseco pistons in 94mm size the coated version has a thinner ring set which we use on normally aspirated engines, the un-coated version has a thicker ring set which is more suitable with a turbo or nitrous set-up, but we have used them normally aspirated in both street and race engines, with no issues.
Prices starting at £330 We also can supply these with a dish to lower compression on a turbo engine, or valve notches, or even both, see pic below. |
Scat Chromoly Cranks
69mm VW Journal, 8 dowel, counter-weighted, chromoly
£305 78.8mm & 82mm Strokes - VW Journal £335 84mm Chevy Journal £400 86mm Chevy Journal £425 |
|
|
Long Cylinders 94mm & 101.6mm
|
Scat Chromoly H-Beam & I-Beam Rods
Super strong H' Beam construction
ARP 2000 12 point bolts 5.4, 5.5 & 5.7 VW Journal £235 set 5.325, 5.5, 5.7 Chevy Journal £249 set I-Beam 5.394 VW Journal £150 set |
|
94mm Mahle Piston and Cylinder Kits,
|
CP High Performance Pistons
We can supply CP Pistons to order, we will occasionally stock these, but recommend custom order as every engines needs are different.
Order time is usually 7 working days. We have this set in stock, designed for a 94mm bore turbo engine, using 22mm wrist pin, these are very strong and capable of high rpm and high boost. £600 |
|
Total Seal 2nd Piston Rings
Total seals excellent 2nd piston ring replacement. Fits Mahle and some Wiseco pistons. from £60 |
Grant 90.5mm or 94mm Ring Set
Complete replacement ring set for Mahle Pistons. £28 |
JE Pistons
|
Manton Hi-Rev 4140 Chromoly Cut-to-length 3/8" Seamless Pushrod
|
|
We can and have supplied JE Pistons, both in 94mm & 101.6mm size, in either 22mm
or 24mm wrist pin size, for N/A or forced induction (Turbo & Nitrous) engines. Prices from £450 |
Heat treated extended tips assure proper seating in both lifter and rocker arm bore cups and will not wear out while under extreme conditions .058" wall .035" wall £69 |
Magnesium 94mm Bore stroker case
Bored for 94's stroker clearanced, full flow, new £800 |
Magnesium Case Bored for 90.5mm
Brand new Mag case, bored for 90.5mm pistons, taped for full-flow, perfect for Bus engines or mild 'Street' engines £750 |
Engle Camshafts
Several grinds in stock, other available to order,
W110 FK42, 43, 44, 45, 46, 47, 48 & FK8, 10, 87, 89 All the bigger versions are pre-clearanced cams, they will not need clearancing upto 86 stoke. £80 each |
Scat,Web & CB Camshafts
We carry a selection of cams from these manufacturers, including
Scat C-35 £60 CB 2298 £75 Web 86b £95 Web Cam available to order |
Cam-shield™ 1-SHOT Break-In/Racing
Treats 4 to 6 quarts of Engine Oil for Break-in or Racing £13.50 |
CB Posi-Seal Cam Plug
Fits all 40hp, 1300, and 1600cc type one engine cases that require grooved cam plugs.
£8.00 |
Silverline Cam Bearings
Dual thrust cam bearings, for use with stronger than standard valve springs.
£17 |
Silverline Main Bearings
These are steel backed bearing sets, good quality and probably the best currently available. Std/Std £35 We also stock .25 and .50 mm, oversize on crank and/or case bearing sets, please ask. |
VW Journal Rod Bearings (undersize)
These are all for re-ground cranks from 0.25mm / 0.010 thou upto 1mm / 0.040
They are all new, but are at least 25 years old and consequently are much better quality than is available currently. £25 per set |
|
Mahle VW journal rod bearings
Standard size Mahle rod bearings for VW journal cranks.
£12 |
Clevite Chevy Journal Rod Bearings
Clevite brand Rod Bearings for standard Chevy journal cranks
£25 |
Engine Gasket Kit
This is what we use on all our own engine builds, proper quality pushrod tube seals, o'rings and oil cooler seals, that actually work and don't dry out and crack.
£12.50 |
Schadek Oil Pump
26mm or 30mm £29 Tapped and plugged for Full Flow use add £6 |
Wix Racing Oil Filter
This is a direct replacement for the 'famous Fram HP1'
In recent years the quality of the HP1 dropped and we found this perfect replacement that is as strong and filters as well as the HP1 did. Will fit most filter head adaptors currently available £15 each |
BugPack Oil Filler Tower
Fits in the place of the stock generator/alternator stand. £25 |
